Home > Fuser Error > Lexmark T614 922 Fuser Error

Lexmark T614 922 Fuser Error

Contents

Fuser errors can be from a cold fuser or an overheated fuser. Thermistor Check: HOT - J2-1 - J2-2 = 2.5K ohms COLD = 150K ohms to 260K ohms Replace fuser assembly Shop For: Lexmark Maintenance Kits Lexmark Fusers fastprintersdotcom 8.232 προβολές 4:58 Lexmark T640 T642 T644 Fuser Maintenance Kit Replacement - Διάρκεια: 5:55. Replace the assys in the following order 1. check over here

A 920 error caused by low line voltage can sometimes be cleared by turning the machine off and then on again. Engine Board 3. ERROR 23 Jam at the duplex unit. Learn more You're viewing YouTube in Greek. http://support.lexmark.com/index?page=content&id=SO1583

920.06 Service Fuser Error

and may not be used without advance written permission of PrinterTechs.com, Inc. Change the contents of the old list and save it as new. Check for 24V at red wire on interlock switch with door closed 4. If the error message goes away with the old fuser unit, please check that the new fuser unit is the correct one for this printer model.

Error 122 Fuser Error - Problem in the fuser, not heating, heating to quickly or too hot. Check paper sensor flag for restricted movement or damage. Remove jammed media Error 250 Paper Jam - Check MP Feeder Paper is jammed in the multipurpose feeder. Lexmark Fuser Replacement Look into the printer from the front.

Error 37 37 Insufficient Collation Memory Memory is too full to collate the print job. Lexmark 924.01 Service Fuser Error Check the continuity of the lamp, the thermal fuse, and the fuser power cable. If you have tried the printer on other wall outletsand the 925 Fuser Error still appears, the printer will require service to clear the message. Roller is approximately 2" in circumference print defects with this repetitive spacing can be caused by transfer roller problems, on a standard 11" page defect would repeat five times.

If this is an intermittent error, you may want to check how the printer is plugged in, even ifit has worked on this surge device for months. 922.02 Service Fuser Error Replace Printhead Pricing Error 934 Printhhead Error - Lost Lock condition Indicates a problem with the mirror motor circuit in the printhead assembly or the mirror motor cable to the system Los Altos Hills, CA Thank you. sometimes i had this problem before.

Lexmark 924.01 Service Fuser Error

If cables, connectors and connections are good replace assemblies listed. this website We do not sell these spare parts.We help you to create your parts sheets to request from your suppliers. 920.06 Service Fuser Error BrokenPrinter1 99.547 προβολές 5:37 Installing the Dell 2335dn fuser maintenance kit, adf pickup and separation pad. - Διάρκεια: 4:58. Service Fuser Error Lexmark Printer Perform fuser service check.

Remove toner cartridge for better access to jammed paper. check my blog Any suggestion would be appreciated.Thanks by unknown on Nov 10, 2009 at 3:19pm Add comment Please sign in to comment Please sign in to comment Lexmark Optra T614 Buy discount ink by aerolaser on Jun 24, 2009 at 8:35am Add comment Please sign in to comment Please sign in to comment Lexmark Optra S Buy discount ink Buy this printer More Lexmark We got it this morning and I have it installed. Lexmark X654de Service Fuser Error

Make sure the memory shown on the printout matches the installed memory. Error 922 Fuser failed to reach standby temperature. It can also be the LVPS (low voltage power supply) or a fuse in the power supply on some models. this content Shop for Lexmark print cartridges Error 32 32 Wrong Print Cartridge installed The installed print cartridge is not supported by the Optra printer.

This gives the printer's engine board a chance to reset. 122.02 Service Fuser Error San Rafael, CA Great that you have that part in stock and thank you for your quick reply. I will have purchasing call in an order.

Check all the connectors to the exit sensor card and the lamp power connections at the left end of the fuser.

If the voltage to the fuser lamp is the not the same as the line voltage,replace the LVPS. Scroll Down to your error code.... If this error appears shortly after the fuser unit in the printer is replaced, put the old fuser unit back in. 925 Service Fuser Error Lexmark T632 If there is no continuity, make sure the HVPS contact returns to its upward limit when depressed, and make sure the left bearing of the transfer roll is making proper contact.

Send an Email Toll Free: 877-365-1903 About us Terms Contact us Help Login Brand : All brands HP Models Lexmark Models Xerox Models Model : Choose a brand by pedrohuerta on Jun 2, 2005 at 3:59pm Add comment Please sign in to comment 0 received reply from lexmark" The “922 Fuser Error” is a cold fuser error. Check the TMC pin in the cartridge contact error for free non binding movement If pin does not move freely you may need to replace the contact assembly. have a peek at these guys Replace Printhead Pricing Error 935 Printhead Error - May have sub-codes.

Replace with the correct printhead. If the signal is OK, replace the LVPS. Make sure fuse is installed correctly, Verfy proper fuser is being used. Error 29 The output bin sensor has not been unmade.See “Output Bin Sensor” on page 2-22.

Can be system board or printhead. Use caution when measuring AC voltages. Can be system board or printhead. Error 54 Serial Error - Framing or parity error on serial.

Make sure the printer is plugged straight to the wall and not through a surge device or power strip. Requires further measurement The printhead (laser scanner) does not contain any serviceable parts. valejet TV 25.894 προβολές 6:13 Installing the Lexmark MS810 MS811 MS812 fuser maintenance kit 40X8420 40X7743 - Διάρκεια: 4:27. Error 26 Duplex unit is installed but paper tray is not sensed.

We have replaced the fuser and still get the same error. VWestlife 33.916 προβολές 6:37 Lexmark T640 Maintenance Kit Instructional Video - Διάρκεια: 10:42. If the paper is jammed in the rear of the duplex, replace the duplex front cover and open the duplex rear door. Error 38 38 Memory Full Memory used to store pages is full.

valejet TV 35.197 προβολές 6:34 Mantenimiento Impresora Laser Lexmark E250d - Διάρκεια: 13:21. If you need the correct part number, you can find it here. Can also be LVPS or system board.