Home > Fuser Error > Lexmark Optra T612 Fuser Error

Lexmark Optra T612 Fuser Error

Contents

For this error on this Lexmark model, the manual ... Lägg till i Vill du titta på det här igen senare? Error 38 38 Memory Full Memory used to store pages is full. Mirror motor unable to reach operational speed, various other component level failures indicated by 935.XX Check cables, look for chafing or damage to ribbon cable at sharp bends around rear weblink

Replace the assys in the following order 1. Remove jammed media Error 90X Software Error Unrecoverable software error. Replace System Board Request Quote Error 917 Check the transfer roller for toner buildup, surface damage to the roller, oil, or other contaminants on the surface of the roller. precisionroller 18 027 visningar 10:42 Lexmark T630 T632 T634 Paper Jam - Open Rear Door.wmv - Längd: 1:59.

920.06 Service Fuser Error

If the 902 error does return,the engine/system board will most likely needto be replaced If you are a technician working on the printer and you replaced the engine/system board,do the following: Transfer Roll Error Cannot start servo operation. Check the toner metering cam on back of suspect cartridge. Paper is either not leaving the duplex entry sensor in time or not making or unmaking the duplex exit sensor in time.

If the Quick Disk Test passes but the disk does not work, run the Disk Test/Clean (2 hr. Any suggestion would be appreciated.Thanks by unknown on Nov 10, 2009 at 3:19pm Add comment Please sign in to comment Please sign in to comment Lexmark Optra T614 Buy discount ink Have a manual for Lexmark Optra T612 Laser Printer? 922.02 Service Fuser Error Replace the Autocompensator Assy.

Contact service person Error 940 LV Power Supply Low voltage power supply cross over test failed. For example: ftp 123.456.78.900 Type bin and press ENTER. Remove jammed media Error 250 Paper Jam - Check MP Feeder Paper is jammed in the multipurpose feeder. http://www.fixyourownprinter.com/posts/29591 Print.Save.Repeat. 9 693 visningar 1:29 Vídeo Recarga Toner Lexmark T630 | T640 | T642 | T644 | X642 | X644 - Vídeo Aula Valejet.com - Längd: 6:34.

fastprintersdotcom 28 944 visningar 4:27 Part 2- Fix or repair color laser printer with fading, light print, or lines samsung clp 300 - Längd: 10:18. 122.02 Service Fuser Error Error 82 Photo Developer Cartridge Exhausted The Photo Develper (OPC belt cartridge) has reached the end of it's life and must be replaced. Run the Quick Disk Test. If an open circuit, replace the lamp or fuser.

924.01 Service Fuser Error

Thank you for the speedy shipment and response.

If the 902 error does return, please go through the checklist below. 920.06 Service Fuser Error or it's affiliates. Lexmark X654de Service Fuser Error Check the continuity of the fuser lamp at the two heavy leads.

John D. have a peek at these guys Open the printer rear door to access the jam. Answer questions, earn points and help others Answer questions Manuals & User Guides PDF Manual . Error 24X Paper Jam - Check Tray "X" Primary: Paper is jammed around Tray X (X=tray 1 thru 5). Lexmark Fuser Replacement

Use caution when measuring AC voltages. Error 52 Flash Full - Not enough flash memory for data requested to be stored. PrintingExperience123 73 087 visningar 6:48 Lexmark T640 T642 T644 Fuser Maintenance Kit Replacement - Längd: 5:55. http://x88software.com/fuser-error/lexmark-optra-s-1855-fuser-error.php Make sure there is no paper jammed in the printer.

Most cost effective solution is to replace the fuser Lexmark Fuser Pricing Error 924 924 Fuser Error - Open circuit detected in thermistor circuit. Lexmark Error Codes See “Network Wrap Tests” on page 23. Verify correct cable connections from the Engine board to the HVPS.

Error 31 Error code 31 is displayed when the top front cover is closed and a defective print cartridge is detected.

ramesh0356 10 263 visningar 18:57 Lexmark Laser Technology Presentation - Längd: 4:47. Logga in om du vill rapportera olämpligt innehåll. Error 58 Duplex Not Attached Duplex is electrically connected but no longer mechanically attached, and printer top cover is closed. Lexmark Support Paper not being picked up check paper tray & pickup rollers Replace rollers if worn smooth or cracked ERROR 21 The exit sensor was not made in time after the input

Verify correct cable connections from the Engine board to the HVPS. eCommerce Solution : k-eCommerce ? Error 923 Fuser is too hot while printing or when idle. • Short in the thermistor circuit. • Noisy thermistor signal • Fuser is actually overheating due to hardware faults. this content Check the left and right transfer roll arm assembly to make sure it is fastened and locked in the down position if applicable to your machine.

Veronica Casto Houston, TX It is nice to place anonline order & get to talk to an actual person. Newer machines display a sub code to indicate which condition applies. Make sure the memory shown on the printout matches the installed memory. Replace Printhead Pricing Error 935 Printhead Error - May have sub-codes.

See “Duplex” on page 2-16 Error 24 The defined paper size is too short to print data as formatted.